Wait.. what? What about the chip? You said it doesn't have to be changed or reset and yet you have changed it?
ciao utilizzo delle cartucce compatibili (Alphalink) che pero' ora la stampante non riconosce piu. Cosa posso fare? sostituire il chip mi sembra una operazione un po complicata... hai consigli? grazie mille!
Thanks alot very detailed instruction
Can you advised which type of refill powder we use it
Wednesday 28/10/2020.
Hello "Viandant5".
I have been using a Brother MFC-L3750CDW for a few months and have recently succeeded in replacing the original four standard capacity cartridges (TN243) by high capacity cartridges (TN247) in "compatible" version, ... this over the course of the period. 'exhaustion of each of these original cartridges ... and preceded by "simple" "resets" of these cartridges, .... until the visible appearance of an excessive exhaustion of each of these cartridges, ... thus motivating their replacements.
I carried out these first "resets" by using the key press combinations allowing to reach the "menu" then to specify the reinitialization of the capacity of each cartridge, with mention of the "standard" capacity of the original cartridges;
Then, when it was necessary to insert the "compatible" cartridges of "high capacity", ... I had to operate, ... at least on some of these "compatible" TN247 cartridges, ... the procedure more " closes "cartridge reset ... by correcting the correct initial position of the" reset gear "(based on one of your videos) ... and then correctly selecting the correct capacity via the" menus " to have their "high capacities" recognized.
Alas, ... after a few impressions (although correct) having followed the placement of the last of the "compatible" cartridges, I was surprised, after switching on, to receive the message "No toner "... which persists despite all my attempts at new resets by the two processes mentioned previously ... and this on each of the four cartridges, ... since the" message "does not tell me which cartridge is not detectable.
I went so far as to check / clean the "contact points" which could, in the printer, allow "physical" detection of the presence of cartridges, ... but this did not bring any improvement.
I am very distraught, ... especially because very soon I should be able to materialize other essential impressions, ... as well as document scans ... which are also refused to me by the equipment, ... causes the message "No toner" to be displayed immediately after switching on the equipment.
Can you provide me with other ways to resolve this "problem" ???
Thanks in advance.
PROOT Guy 8-)
"guy.proot@gmail.com"
Superb.. My issue got resolved.. Thanks a ton
Hello, can i put TN-261 catrige wrk in place of TN-263 or TN-267 in dcp l3551 cdw plz suggest me
EXCELLENT video!! Just one item to make it better, do you have a recommended webpage to get the replacement toner? Thanks again!!!!
It seems there are 2 methods to reset TN-243/247 cartridges:
1. The reset gear shown in this video
2. The software reset shown in your other video: https://www.youtube.com/watch?v=6WAb2C3Wgq4
What's the difference? Which reset method is better?
I'm guessing that MAYBE the software reset is only a "soft" reset, but when the reset gear reaches the end position, the software counter is ignored, and the cartridge is shown as empty. Then you can only reset it with the reset gear, but not the software reset method. Right? I don't know, that's just my guess how these 2 reset methods interact with each other.
I have a problem and I' don't know why is this happening. I have an alternative tonner TN 2340 and I've tried refill it a couple of times. The thing is for some reason the center gear shaft, the next to the reset gear just stop spinning and get stuck, so the system doesn't work any more. I don't know why this is happening. The first time I did it I fucked it up, te gear shaft got stuck. The second time, no problem and all worked fine. Now, the third time I'm doing the procces the gear shaft is stucked again. I don't know what to do, please help.
Is it possible to reset the demo cartridge TN-263 that came with the printer.
I have purchased one compatible cartridges that has the reset gear. I tried resetting the other cartridges but i was unsuccessful, may be i did it wrong, is it necesscary to turn the gear with hand as you have shown in the video 6:50. Please reply.
Hello, will TN-247 wrk in place of TN-263 or TN-267 in HLL3270CDW?
Thank you very much for detailed instructions. I lost the small gear ( not the reset gear)while filling the cartridge.Is there any way to replace it? Thanks
What are the main differences between TN223(latest printers) and TN221(older printers) cartridges? Would it be beneficial to upgrade an old Brother printer with TN221 cartridges to a new printer with TN223? Thank you.
very very thank you
Grazie per la guida, arrivo qui perchè il metodo di reset illustrato sul video "Resettaggio Cartuccia Toner Brother MFC-3700 TN243 TN247" non funziona più dopo l'aggiornamento del firmware, e io da pollo ho lasciato la stampante aggiornare il firmware. Dato il mio modello (DCP-L3550CDW) ha toner senza quell'ingranaggio, che alternative ci sono per continuare ad utilizzare i toner installati? Grazie.
Can I use methylated spirit for cleaning rollers?
where can I buy the reset gear with the spring?
This toner has as refill plug in the left please use that to refill not via doctor blade
Nice can you please tell me how to refill torner tn263 and tn267 bk
What firmware version do you have in the HL-L3210 unit? Mine was shipped with a very recent version (1.22, issued in 2019), does the refill works without replacing the chip on a 1.22 firmware unit too? Thanks!
MY 3270CDW is still showing to replace new toner, even I plug a new or refill toner. How can I do, Sir. Thx
i have brother dcp L3551cdw printer this cartridges tn-263 this come with new printer how can put reset gear in plz help me
what if the foam roller is damaged? does it have any effect?
Thanks for the upload, year 2020 and valid.
I love you
When it talks about the number of grams to put in, is that the amount put in by the factory? Can I put more in if I have it? Can you near fill the cartridges, or does that make issues?
Anyone needs a TN-221 CYMK for only 20 dollars? Give me an email! :) We can still lower this.
He hecho lo mismo pero no reconoce la impresora el toner. Que puede ser?
Hi.what happens if you put more toner?
I think the original toner cartridge is too expensive. I prefer a compatible product. However, they are also very good. https://www.amazon.com/Cartridges-Replacement-Brother-MFC-9130CW-HL-3170CDW/dp/B07FD718BM/ref=sr_1_73?ie=UTF8&qid=1540536205&sr=8-73&keywords=brother+mfc-9130cw++toner
and what about if cartridges are cheaped ?
Where to get good quality toner powder ?
good intiniative , from india tamilnadu state its me SUNAI SYSTEMS AND SOLUTIONS please contact these original suppliers to my mobile 91- 9751578870 or sunaisystems@hotmail.com , we need these compatiable toner and resetting gear bulk.
reset gear and spring need buy? ty
Have Brother HL-3170DCW
TN-221
I got all the process of disassembled and clean.
But my cartridges don't have reset gear, I don't need it if I reset it feel. The printer is that correct
Thank ahed of time for your help
inkwelcome7@gmail.com
Great advice, thanks. It should be noticed that the "cover" has to be ALL THE WAY open for the "asterisk press" for 5 seconds to be accepted, and the reset screen to appear. At least, that was my experience.. ":
thanks
Scusami se in qualche modo ti abbia offeso, non era mia intenzione. Credo però che noi abbiamo delle resposabilità morali nei confronti di chi vede in particolare di quelle persone che fanno il fai da te ed è convinto che funzioni così. Quandi, ribadisco che Non voglio in alcun modo fare nessuna forma di polemica. Buon lavoro.
In Italia se ti vedono pulire le cartucce come quel operaio che la puliva fuori dal capannone senza nessuna norma di sicurezza, avrebbero arrestato il titolare e fatto chiudere l'azienda. Non vi sembra di esagerare. E' tutto troppo semplice!!! Immagino come stampa!!! Avete preso una cartuccia compatibile perchè semplice da togliere il tappo, fatelo con l'originale. Come al solito, come fà a resettare il toner con l'ingranaggio messo così?
Life saver Video *****
Didn't work for me!!Every time i tried to print from my Brother MFC J430 it prints blank pages and that too very slowly. Finally i had to contact Brother 𝟏_𝟖𝟎𝟎_𝟗𝟕𝟓_𝟎𝟏𝟒𝟖 for resolving my issue. The only reason I actually tried this was because of all the reviews saying it works. Thank you anyways!!!!
Not working anymore, probably an update on the printer...
I've been using your fix it for years! Thank you!
I have this saved for my office printer. I do this all the time now and my work has saved a lot of money on ink!!! THANK YOU
Thanks for the video ! 👍
This works so well! It adds another month or so of printing. Thank you so much.
Thanks Matthew. I had read many ways to reset that were what you were saying but your video made it so clear and easy. After I watched your video I had it done within two minutes. The key was when you showed how to use the *. None of the other written instructions had said that you had to remember where it was to press. I kept trying to open the fax again and press and it wasn't working. So thanks for your clear instructions.
Make sure the warning "Please close the front cover" is displayed on the screen before you press the asterisk for 5 seconds. If that screen is not displayed, then it will not work.
Great Stuff thanks for that all working well now
Very helpful, thank you
So glad I found your video, I've been trying to print my assignments and the printer kept telling me to replace yellow toner, I wasn't even printing in colour! I put a circle around the * with a felt pen to make it easy to find.
Also my printer is an MFC-9335CDW but your instruction still worked fine. Thank you.
Thanks! it worked for me! :)
Thank you. You have saved me lots of money over the last five years by showing me here how not to have to replace Brother Black Ink cartridges that still have hundreds of pages of ink still left in them.
Super helpful, thank you!
Gary. Many thanks for this clever tip to get the most from each of toner cartridges
Thank you! Thank you! Thank you!
Ahhh thank you !!!
Didn’t work for me -when I hit the star and waited for 5 seconds. I tried dozens of times. Any ideas
It took only 1 mash for me to reset the cartridge but took several tries on my first time attempt to get the reset menu to come up. I always select reset high capacity to make it last longer between resets.